List of DURACON ® POM grades: This page’s PDF (0.97MB) 6. Molding Characteristics. 6.2 Mold Shrinkage . Fig. 6-5 Mold shrinkage of M90-44 (side gate) Fig. 6-6 Mold shrinkage of M90-44 (pin gate) Molding conditions: Injection pressure: 50MPa Cylinder temp.: 190°C Mold temp.: 80°C …
M90-44. The mold shrinkage ratio for M140-44 is shown in Figure 2-7, while that for M270-44 is shown in Figures 2-8 and 2-9. One can see that it is acceptable to design molds as for M90-44. Mold shrinkage for M450-44 is shown in Tables 2-4, 2-10, and 2-11. Table 2-3 DURACON ® POM M90-44 mold shrinkage (Unit : %) Fig. 2-7 DURACON ® POM M140-44 …
acceptable to design molds as for M90-44. Mold shrinkage for M450-44 is shown in Tables 2-4, 2-10, and 2-11. Table 2-3 DURACON ® M90-44 mold shrinkage (Unit : %) Fig. 2-7 DURACON ® M140-44 mold shrinkage Processing parameters Material temperature : 200°C Mold temperature : 80°C Injection speed : 25mm/s Mold cavity : 120×120×1~3mm, Fig. 4-10 shows approximate times to knock out DURACON ® POM M90-44 molded products as obtained by actual measurement and calculation. In general, holding pressure time should be a little longer than gate sealing time as mentioned before. Cooling time is determined by plasticating time plus product knockout time (holding pressure and cooling time).
DURACON ® M90-44 is an Acetal ( POM ) Copolymer product. It can be processed by injection molding and is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America. Typical application: Automotive. Primary characteristic: flame rated.
Polyplastics Duracon® M90-44/M90S Acetal Co-polymer (POM), Standa…, DURACON® M90-44 (POM) by Polyplastics – Technical …
10/21/2019 · DURACON® M90-44 is a polyoxymethylene ( POM) polyacetal grade. Possesses good mechanical & snap-fit properties and thermal stability. Offers superior moldability & good fuel-, chemical and grease resistance. Is suitable for processing by injection molding.
Polyplastics Duracon ® M90-44/M90S Acetal Co-polymer (POM), Standard, General Category : Polymer , Thermoplastic , Acetal ( POM ) , Acetal Copolymer, Unreinforced Material Notes: DURACON ® is a crystalline thermoplastic acetal copolymer. The primary raw material trioxane, a trimer of formaldehyde.The thermoplastic, Acetal Co-polymer ( POM ), Standard, General, DURACON ® is a crystalline thermoplastic acetal copolymer. The primary raw material trioxane, a trimer of formaldehyde. The thermoplastic adopts a copolymer structure in which polyoxymethylene (-C-O) and, DURACON NW-02 exhits higher flowability than do the conventional wear-resistant grades, which may result in higher productivity and higher dimensional accuracy in molding (Fig. 3-1). Fig. 3-1 Bar flow length (2mmt) 3.2 Molding Shrinkage DURACON NW-02 shows molding shrinkage approximately the same as that of AW-01 or SW-01 (Fig. 3-2).
Polyplastics Duracon ® M90-44/M90S Acetal Co-polymer ( POM ), Standard, General Polyplastics Duracon ® M90-45 Acetal Co-polymer ( POM ), Weather resistance, General Polyplastics Duracon ® M90-48 Acetal Co-polymer ( POM ), Antistatic, General
